Duo3 Gold specifications can be found at the bottom of the page.
Duo3 specifications can be found at the bottom of the page.
Duo2 GT specifications can be found at the bottom of the page
Duo2se specifications can be found at the bottom of the page
Duo2 specifications can be found at the bottom of the page
DuoX specifications can be found at the bottom of the page
Duo specifications can be found at the bottom of the page
DuoX specifications can be found at the bottom of the page

Duo 3 Ultra Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

If there are any mistakes in the diagrams. Please email us and let us know. Thank you.

Possible placement of chips. 

The Duo 3 Ultra Chip has 3 boot modes.

Fully Auto detect PS2, PSX and movie mode

Disable Mode

- Hold  the START  button on joypad 1 until "DISABLED" appears on the TV.
- press RESET button and the chip will remain in disable mode until the PS2 is power down again.

Boot from memory card

- From reset, hold R1 button on joypad 1 to boot installed application on memory card. (mc:BOOT/BOOT.ELF)

A lot of people have asked us how to installed useful programs to the memory card. We found the following site quite useful. Hopefully, the sites owner doesn't mind us linking to it.

http://www.geocities.com/zebradudeman/

Boot from HHD (old machines)

- From reset, hold R2 button on joypad 1 to boot installed application on HDD. 

A lot of people have asked us how to installed useful programs to the memory card. We found the following site quite useful. Hopefully, the sites owner doesn't mind us linking to it.

http://www.geocities.com/zebradudeman/

Additional information

V9 and v10 LA chip syndrome.
It is a well documented fact that the latest v9 and v10 machines suffer from a major problem. The LA chip has a tendency to die. After it dies, the only solution to get your machine working again is to replace the chip with an original LA6508 or a device called LA6508 RII. However, in both cases, it is quite a hard soldering job. (much harder than to install a chip). The following can be done to reduce the chances of the LA 6508 chip dying. Again do not attempt the simple modification unless you know what you are doing.

The original article can be found at  http://cyber-mag.com/station/

Firstly - the prevention - by far easier than the cure:
1) Carefully lift Pin17 of the LA6508 Chip,
2) Ensure no solder links it to the pad it was just lifted from,
3) Link Pin17 to 5 volts as demonstrated in the picture below.

V9 diagram.

v10 diagram.
another v10 diagram

DuoX 2 GS Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

Xbox (Pal, US, Asian, Jap)

Version 1.0

Version 1.1

Version 1.2 and Version 1.3

Version 1.4

Version 1.5

Version 1.6

Please note that the Chip can have either of the following printed on it. AMD, HYUNDAI, FUJITSU

Installing pin socket to chip. (diagrams are by Arakon)

Soldering pin socket to chip.

DuoX 2 GS has 2 boot modes.

- DuoX 2 GS Enabled
- DuoX 2 GS Disabled.

It is assumed that your machine is in the Power Off  mode, ie machine is not switched on

DuoX 2 GS Mode (Duo-X enabled)

Bank 0 bios for v1-v1.5 xbox                        Bank 1 bios for v1-v1.6

- Power on Xbox with the "Power" button.

Original Bios Mode (Duo-X disabled)

- Power on Xbox with the "Eject" button.

Please note: To change between modes, the xbox  must be put into power off mode.

Additional information

How can I tell which version Xbox do I have?
- Please check xbox-scene. Click here for the version page.

Examples of installs?
Wire
Direct
Header

Bios?
- It is your decision whether to flash it with a different bios. However, we do not recommend it though. This is because we believe for most people, there is really no need for it.
(However, due to restrictions of certain countries. Your chip might not come with a working bios.)

What do I have to add to evox.ini?
- The latest version of EvolutionX should already contain the relevant information.

ie. 
0x01d5,"AMD - Am29F080B",0x100000
0x04d5,"FUJITSU - MBM29F080A",0x100000
0xadd5," HYUNDAI - HY29F080",0x100000

Xbox Live?
- If you ever log onto Xbox Live with the chip enabled. That particular xbox  eeprom  would then be banned permanently.

DuoX 2  GS Cromwell/FlashBios Edition

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

Xbox (Pal, US, Asian, Jap)

Version 1.0

Version 1.1

Version 1.2 and Version 1.3

Version 1.4

Version 1.5

Version 1.6

Installing pin socket to chip. (diagrams are by Arakon)

Soldering pin socket to chip.

DuoX 2 GS has 2 boot modes.

- DuoX 2 GS  Enabled
- DuoX 2 GS Disabled.

It is assumed that your machine is in the Power Off  mode, ie machine is not switched on

Memory Banks

Bank 0

Bank 0 contains the latest Cromwell bios. To flash it we would usually recommend the Eurasia generic pro flash disc. And please note that you will need a 512KB bios (ie 2 X 256KB of the same bios since most bios are only 256KB)

1.6 -1.6b machines will need the m8+ 1.6 bios.

1.0-1.5 machines can use either the m8+ bios (non 1.6) or the Xecuter 4983 bios.

Or you should be able to use this bios for running xbox linux.

Further details regarding linux and xbox in general can be found at www.xbox-scene.com and at www.xbox-linux.org

Bank 1

Bank 1 contains the latest FlashBios (3.03-1). Please note that you will need a 512KB bios (ie 2 X 256KB of the same bios since most bios are only 256KB)

1.6 -1.6b machines will need the m8+ 1.6 bios.

1.0-1.5 machines can use either the m8+ bios (non 1.6) or the Xecuter 4983 bios.

FlashBios tutorial can be found at the following website.

http://www.teamxecuter.com/flashbios/

How to use FlashBIOS:

Step 1 - Creating the Bios CD:

- Ensure that the bios file you wish to use of an appropriate size for your modchip. ( 512KB in this case)

- Make a copy of the bios file you wish to use and rename this copy to BIOS.BIN .

- Select a CD or DVD media compatible with your XBox's DVD-Rom. (Most CDRW will work and most DVD-R will work. If you have a Samsung Drive then some CD-R will work)

- Burn the BIOS.BIN file onto a CD. (For Nero select the following settings, No Multisession, ISO Level 1, Format Mode 1, ISO 9660, Deselect Joliet, Finalize CD, Disc-At-Once)

- You should add a dummy file to the CD to ensure it is read properly by the XBOX. We have enclosed a dummy file creator with this release. We recommend 100MB.

Step 2 - Flashing with FlashBIOS (Cromwell):

- Turn your XBox console ON, when the DVD-Rom tray ejects please insert your BIOS.BIN CD and close the tray.

- When the flashing procedure is complete the XBox will shut down.

DuoX 2 Lite Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

Xbox (Pal, US, Asian, Jap)

Version 1.0

Version 1.1

Version 1.2 and Version 1.3

Version 1.4

Version 1.5

Version 1.6

Please note that the Chip can have either of the following printed on it. AMD,

Installing pin socket to chip. (diagrams are by Arakon)

Soldering pin socket to chip.

DuoX 2 Lite has 2 boot modes.

- DuoX 2 Lite Enabled
- DuoX 2 Lite Disabled.

It is assumed that your machine is in the Power Off  mode, ie machine is not switched on

DuoX 2  Lite Mode (Duo-X 2 Lite enabled)

- Power on Xbox with the "Power" button.

Original Bios Mode (Duo-X 2 disabled)

- Power on Xbox with the "Eject" button.

Please note: To change between modes, the xbox  must be put into power off mode.

Additional information

How can I tell which version Xbox do I have?
- Please check xbox-scene. Click here for the version page.

Examples of installs?
Wire
Direct
Header

Bios?
- It is your decision whether to flash it with a different bios. However, we do not recommend it though. This is because we believe for most people, there is really no need for it.
(However, due to restrictions of certain countries. Your chip might not come with a working bios.)

What do I have to add to evox.ini?
- The latest version of EvolutionX should already contain the relevant information.

ie. 
0x01a4,"AMD",0x80000
0x04a4,"FUJITSU ",0x80000

Xbox Live?
- If you ever log onto Xbox Live with the chip enabled. That particular xbox  eeprom  would then be banned permanently.

Duo Q Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

GC  (Pal, US, Asian, Jap)

Operating instructions

No special operating instructions required. Operating instruction is the same as a normal GQ.

DuoWii Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

Diagram from a user "Flash78"

Flash78 diagram

Operating instructions

No special operating instructions required. Operating instruction is the same as a normal Wii.

Disable Mode

- Make sure no disc is in machine and the machine is in standby mode.

- Hold POWER and RESET button to start machine. Keep holding the buttons until DuoWii indicator LED switches off.

- Your chip is now in disable mode.

Warning about upgrading the Wii.

Please be careful when a game ask you to upgrade firmware. This is because if the game is an import, the import upgrade firmware can render your machine unusable. The following is a link to a website that helps you to reduce the chance of rendering your machine unusable. It contains a list of what import games can be used for upgrade and also a list of what import games might work on your mahcine. However, there are sometimes mistakes on that list. So be careful with firmware upgrades.

Wii compatibility list

Special Note: current version of DuoWii does not support the backup version of Super Mario Galaxy. However, the origina should work fine in disable mode. If in the future there is a way around this problem, the solution will be announced here.

Duo 3 Gold Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

Possible placement of chips. 

The Duo 3 Gold Chip has 3 boot modes.

Fully Auto detect PS2, PSX and movie mode

Disable Mode

- Hold  the START  button on joypad 1 until "DISABLED" appears on the TV.
- press RESET button and the chip will remain in disable mode until the PS2 is power down again.

Boot from memory card

- From reset, hold R1 button on joypad 1 to boot installed application on memory card. (mc:BOOT/BOOT.ELF)

Additional information

Possible power issue.
On certain chip and machine combination. It maybe useful to try the alternative power point. Diagram of alternative point.  

V9 and v10 LA chip syndrome.
It is a well documented fact that the latest v9 and v10 machines suffer from a major problem. The LA chip has a tendency to die. After it dies, the only solution to get your machine working again is to replace the chip with an original LA6508 or a device called LA6508 RII. However, in both cases, it is quite a hard soldering job. (much harder than to install a chip). The following can be done to reduce the chances of the LA 6508 chip dying. Again do not attempt the simple modification unless you know what you are doing.

The original article can be found at  http://cyber-mag.com/station/

Firstly - the prevention - by far easier than the cure:
1) Carefully lift Pin17 of the LA6508 Chip,
2) Ensure no solder links it to the pad it was just lifted from,
3) Link Pin17 to 5 volts as demonstrated in the picture below.

V9 diagram.

v10 diagram.
another v10 diagram

Duo 3 Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

Possible placement of chips. 

The Duo 3  Chip has 3 boot modes.

- PS2 mode (LED will produce a steady light)
- PSX mode (LED light will flash slowly once before PSX logo)
- Disable mode (LED will not light up)

Fully Auto detect PS2, PSX and movie mode

or you can follow the following  instructions if you do not like the auto detect mode.

It is assumed that your machine is in the Standby mode, ie machine is not switched on

PS2 games

Method 1:
-Press EJECT button to switch on the machine.
-Insert PS2 game in tray.
-Tap RESET button once, the machine would reboot and then load your game.

Method 2:
- Press EJECT button to switch on the machine.
- Insert PS2 game in tray, the press EJECT button to close tray.
- The disc will then take 2-5 seconds to be recognized and then boot.

To boot another game when already playing a game.
- Press EJECT button.
- The current game would then pause and the tray would come out.
- Change to another PS2 game disc and tap RESET button once.
- The machine would reboot and then load your game.

PSX games

- Press EJECT button to switch on the machine.
- Insert PSX game in tray, then press and hold RESET button to switch off machine.
- Now hold the RESET button to start up your machine. Only release the RESET button once the Blue LED light of the Eject button lights up.

DVD movies

- Press EJECT button to switch on the machine.
- Insert DVD movie in tray, then press and hold RESET button to switch off machine.
- Now hold the RESET button to start up your machine. Only release the RESET button until the "blue clouds" comes up on the TV.

Disable Mode

- Hold  the RESET button until the "blue clouds" comes up on the TV.

Additional information

V9 and v10 LA chip syndrome.
It is a well documented fact that the latest v9 and v10 machines suffer from a major problem. The LA chip has a tendency to die. After it dies, the only solution to get your machine working again is to replace the chip with an original LA6508 or a device called LA6508 RII. However, in both cases, it is quite a hard soldering job. (much harder than to install a chip). The following can be done to reduce the chances of the LA 6508 chip dying. Again do not attempt the simple modification unless you know what you are doing.

The original article can be found at  http://cyber-mag.com/station/

Firstly - the prevention - by far easier than the cure:
1) Carefully lift Pin17 of the LA6508 Chip,
2) Ensure no solder links it to the pad it was just lifted from,
3) Link Pin17 to 5 volts as demonstrated in the picture below.

V9 diagram.

v10 diagram.
another v10 diagram

Duo 2  GT Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

Possible placement of chips. 

The Duo 2 GT Chip has 3 boot modes.

- PS2 mode (LED will produce a steady light)
- PSX mode (LED will flash)
- Disable mode (LED will not light up)

It is assumed that your machine is in the Standby mode, ie machine is not switched on

PS2 games

Method 1:
-Press EJECT button to switch on the machine.
-Insert PS2 game in tray.
-Tap RESET button once, the machine would reboot and then load your game.

Method 2:
- Press EJECT button to switch on the machine.
- Insert PS2 game in tray, the press EJECT button to close tray.
- The disc will then take 2-5 seconds to be recognized and then boot.

To boot another game when already playing a game.
- Press EJECT button.
- The current game would then pause and the tray would come out.
- Change to another PS2 game disc and tap RESET button once.
- The machine would reboot and then load your game.

PSX games

- Press EJECT button to switch on the machine.
- Insert PSX game in tray, then press and hold RESET button to switch off machine.
- Now hold the RESET button to start up your machine. Only release the RESET button once the Blue LED light of the Eject button lights up.

DVD movies

- Press EJECT button to switch on the machine.
- Insert DVD movie in tray, then press and hold RESET button to switch off machine.
- Now hold the RESET button to start up your machine. Only release the RESET button until the "blue clouds" comes up on the TV.

Disable Mode

- Hold  the RESET button until the "blue clouds" comes up on the TV.

Additional information

V9 and v10 LA chip syndrome.
It is a well documented fact that the latest v9 and v10 machines suffer from a major problem. The LA chip has a tendency to die. After it dies, the only solution to get your machine working again is to replace the chip with an original LA6508 or a device called LA6508 RII. However, in both cases, it is quite a hard soldering job. (much harder than to install a chip). The following can be done to reduce the chances of the LA 6508 chip dying. Again do not attempt the simple modification unless you know what you are doing.

The original article can be found at  http://cyber-mag.com/station/

Firstly - the prevention - by far easier than the cure:
1) Carefully lift Pin17 of the LA6508 Chip,
2) Ensure no solder links it to the pad it was just lifted from,
3) Link Pin17 to 5 volts as demonstrated in the picture below.

V9 diagram.

v10 diagram.
another v10 diagram

Duo 2  SE Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

Possible placement of chips. 

The Duo 2 SE Chip has 3 boot modes.

- PS2 mode
- PSX mode
- Disable mode

It is assumed that your machine is in the Standby mode, ie machine is not switched on

PS2 games

Method 1:
-Press EJECT button to switch on the machine.
-Insert PS2 game in tray.
-Tap RESET button once, the machine would reboot and then load your game.

Method 2:
- Press EJECT button to switch on the machine.
- Insert PS2 game in tray, the press EJECT button to close tray.
- The disc will then take 2-5 seconds to be recognized and then boot.

To boot another game when already playing a game.
- Press EJECT button.
- The current game would then pause and the tray would come out.
- Change to another PS2 game disc and tap RESET button once.
- The machine would reboot and then load your game.

PSX games

- Press EJECT button to switch on the machine.
- Insert PSX game in tray, then press and hold RESET button to switch off machine.
- Now hold the RESET button to start up your machine. Only release the RESET button once the Blue LED light of the Eject button lights up.

DVD movies

- Press EJECT button to switch on the machine.
- Insert DVD movie in tray, then press and hold RESET button to switch off machine.
- Now hold the RESET button to start up your machine. Only release the RESET button until the "blue clouds" comes up on the TV.

Disable Mode

- Hold  the RESET button until the "blue clouds" comes up on the TV.

Additional information

V9 and v10 LA chip syndrome.
It is a well documented fact that the latest v9 and v10 machines suffer from a major problem. The LA chip has a tendency to die. After it dies, the only solution to get your machine working again is to replace the chip with an original LA6508 or a device called LA6508 RII. However, in both cases, it is quite a hard soldering job. (much harder than to install a chip). The following can be done to reduce the chances of the LA 6508 chip dying. Again do not attempt the simple modification unless you know what you are doing.

The original article can be found at  http://cyber-mag.com/station/

Firstly - the prevention - by far easier than the cure:
1) Carefully lift Pin17 of the LA6508 Chip,
2) Ensure no solder links it to the pad it was just lifted from,
3) Link Pin17 to 5 volts as demonstrated in the picture below.

V9 diagram.

v10 diagram.
another v10 diagram

Duo 2 Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

Possible placement of the chip on a
v9
v10

The Duo 2 Chip has 3 boot modes.

- PS2 mode
- PSX mode
- Disable mode

It is assumed that your machine is in the Standby mode, ie machine is not switched on

PS2 games

Method 1:
-Press EJECT button to switch on the machine.
-Insert PS2 game in tray.
-Tap RESET button once, the machine would reboot and then load your game.

Method 2:
- Press EJECT button to switch on the machine.
- Insert PS2 game in tray, the press EJECT button to close tray.
- The disc will then take 2-5 seconds to be recognized and then boot.

To boot another game when already playing a game.
- Press EJECT button.
- The current game would then pause and the tray would come out.
- Change to another PS2 game disc and tap RESET button once.
- The machine would reboot and then load your game.

PSX games

- Press EJECT button to switch on the machine.
- Insert PSX game in tray, then press and hold RESET button to switch off machine.
- Now hold the RESET button to start up your machine. Only release the RESET button once the Blue LED light of the Eject button lights up.

DVD movies

- Press EJECT button to switch on the machine.
- Insert DVD movie in tray, then press and hold RESET button to switch off machine.
- Now hold the RESET button to start up your machine. Only release the RESET button until the "blue clouds" comes up on the TV.

Disable Mode

- Hold  the RESET button until the "blue clouds" comes up on the TV.

Additional information

V9 and v10 LA chip syndrome.
It is a well documented fact that the latest v9 and v10 machines suffer from a major problem. The LA chip has a tendency to die. After it dies, the only solution to get your machine working again is to replace the chip with an original LA6508 or a device called LA6508 RII. However, in both cases, it is quite a hard soldering job. (much harder than to install a chip). The following can be done to reduce the chances of the LA 6508 chip dying. Again do not attempt the simple modification unless you know what you are doing.

The original article can be found at  http://cyber-mag.com/station/

Firstly - the prevention - by far easier than the cure:
1) Carefully lift Pin17 of the LA6508 Chip,
2) Ensure no solder links it to the pad it was just lifted from,
3) Link Pin17 to 5 volts as demonstrated in the picture below.

V9 diagram.

v10 diagram.
another v10 diagram

DuoX 2 Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

Xbox (Pal, US, Asian, Jap)

Version 1.0

Version 1.1

Version 1.2 and Version 1.3

Version 1.4

Version 1.5

Version 1.6

Please note that the Chip can have either of the following printed on it. AMD, HYUNDAI, FUJITSU

Installing pin socket to chip. (diagrams are by Arakon)

Soldering pin socket to chip.

DuoX 2 has 2 boot modes.

- DuoX 2 Enabled
- DuoX 2 Disabled.

It is assumed that your machine is in the Power Off  mode, ie machine is not switched on

DuoX 2 Mode (Duo-X enabled)

Bank 0 bios for v1-v1.5 xbox                        Bank 1 bios for v1-v1.6

- Power on Xbox with the "Power" button.

Original Bios Mode (Duo-X disabled)

- Power on Xbox with the "Eject" button.

Please note: To change between modes, the xbox  must be put into power off mode.

Additional information

How can I tell which version Xbox do I have?
- Please check xbox-scene. Click here for the version page.

Examples of installs?
Wire
Direct
Header

Bios?
- It is your decision whether to flash it with a different bios. However, we do not recommend it though. This is because we believe for most people, there is really no need for it.
(However, due to restrictions of certain countries. Your chip might not come with a working bios.)

What do I have to add to evox.ini?
- The latest version of EvolutionX should already contain the relevant information.

ie. 
0x01d5,"AMD - Am29F080B",0x100000
0x04d5,"FUJITSU - MBM29F080A",0x100000
0xadd5," HYUNDAI - HY29F080",0x100000

Xbox Live?
- If you ever log onto Xbox Live with the chip enabled. That particular xbox  eeprom  would then be banned permanently.

DuoX 2 Cromwell/FlashBios Edition

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

Xbox (Pal, US, Asian, Jap)

Version 1.0

Version 1.1

Version 1.2 and Version 1.3

Version 1.4

Version 1.5

Version 1.6

Installing pin socket to chip. (diagrams are by Arakon)

Soldering pin socket to chip.

DuoX 2 has 2 boot modes.

- DuoX 2 Enabled
- DuoX 2 Disabled.

It is assumed that your machine is in the Power Off  mode, ie machine is not switched on

Memory Banks

Bank 0

Bank 0 contains the latest Cromwell bios. To flash it we would usually recommend the Eurasia generic pro flash disc. And please note that you will need a 512KB bios (ie 2 X 256KB of the same bios since most bios are only 256KB)

1.6 -1.6b machines will need the m8+ 1.6 bios.

1.0-1.5 machines can use either the m8+ bios (non 1.6) or the Xecuter 4983 bios.

Or you should be able to use this bios for running xbox linux.

Further details regarding linux and xbox in general can be found at www.xbox-scene.com and at www.xbox-linux.org

Bank 1

Bank 1 contains the latest FlashBios (3.03-1). Please note that you will need a 512KB bios (ie 2 X 256KB of the same bios since most bios are only 256KB)

1.6 -1.6b machines will need the m8+ 1.6 bios.

1.0-1.5 machines can use either the m8+ bios (non 1.6) or the Xecuter 4983 bios.

FlashBios tutorial can be found at the following website.

http://www.teamxecuter.com/flashbios/

How to use FlashBIOS:

Step 1 - Creating the Bios CD:

- Ensure that the bios file you wish to use of an appropriate size for your modchip. ( 512KB in this case)

- Make a copy of the bios file you wish to use and rename this copy to BIOS.BIN .

- Select a CD or DVD media compatible with your XBox's DVD-Rom. (Most CDRW will work and most DVD-R will work. If you have a Samsung Drive then some CD-R will work)

- Burn the BIOS.BIN file onto a CD. (For Nero select the following settings, No Multisession, ISO Level 1, Format Mode 1, ISO 9660, Deselect Joliet, Finalize CD, Disc-At-Once)

- You should add a dummy file to the CD to ensure it is read properly by the XBOX. We have enclosed a dummy file creator with this release. We recommend 100MB.

Step 2 - Flashing with FlashBIOS (Cromwell):

- Turn your XBox console ON, when the DVD-Rom tray ejects please insert your BIOS.BIN CD and close the tray.

- When the flashing procedure is complete the XBox will shut down.

Duo-X Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

Xbox (Pal, US, Asian, Jap)

Version 1.0

Version 1.1

Version 1.2 and Version 1.3

Version 1.4

Version 1.5

Duo-X has 2 boot modes.

- Duo-X Enabled
- Duo-X Disabled.

It is assumed that your machine is in the Power Off  mode, ie machine is not switched on

Duo-X Mode (Duo-X enabled)

- Power on Xbox with the "Power" button.

Original Bios Mode (Duo-X disabled)

- Power on Xbox with the "Eject" button.

Please note: To change between modes, the xbox  must be put into power off mode.

Additional information

How can I tell which version Xbox do I have?
- Please check xbox-scene. Click here for the version page.

Examples of installs?
Wire
Direct
Header

Bios?
- It is your decision whether to flash it with a different bios. However, we do not recommend it though. This is because we believe for most people, there is really no need for it.
(However, due to restrictions of certain countries. Your chip might not come with a working bios.)

Possible bios
M7 (but you will need to do your own colour mod).
4979.67

What do I have to add to evox.ini?
- The latest version of EvolutionX should already contain the relevant information.

ie. 
0x01d5,"AMD - Am29F080B",0x100000
0x04d5,"FUJITSU - MBM29F080A",0x100000

Xbox Live?
- If you ever log onto Xbox Live with the chip enabled. That particular xbox  eeprom  would then be banned permanently.

Duo Chip

Diagrams

Please use "Right Click" and "Save as" (each diagram is around 500k.)

The Duo Chip has 3 boot modes.

- PS2 mode
- PSX mode
- Disable mode

It is assumed that your machine is in the Standby mode, ie machine is not switched on

PS2 games

Method 1:
-Press EJECT button to switch on the machine.
-Insert PS2 game in tray.
-Tap RESET button once, the machine would reboot and then load your game.

Method 2:
- Press EJECT button to switch on the machine.
- Insert PS2 game in tray, the press EJECT button to close tray.
- The disc will then take 2-5 seconds to be recognized and then boot.

To boot another game when already playing a game.
- Press EJECT button.
- The current game would then pause and the tray would come out.
- Change to another PS2 game disc and tap RESET button once.
- The machine would reboot and then load your game.

PSX games

- Press EJECT button to switch on the machine.
- Insert PSX game in tray, then press and hold RESET button to switch off machine.
- Now hold the RESET button to start up your machine. Only release the RESET button once the Blue LED light of the Eject button lights up.

DVD movies

- Press EJECT button to switch on the machine.
- Insert DVD movie in tray, then press and hold RESET button to switch off machine.
- Now hold the RESET button to start up your machine. Only release the RESET button after like 4-5 seconds.

Disable Mode

- Hold  the RESET button for  like 4-5 seconds to boot up your machine.